PWR-C45-1300ACV Specification |
|
| AC-input type | Autoranging input with power factor corrector
Note Power factor correction is a standard feature on all Catalyst 4500 E-series AC-input power supplies. PFC reduces the reactive component in the source AC current allowing higher power factors (typically 99 percent or better) and lower harmonic current components. |
| AC-input voltage | Low-line (120 VAC nominal)—85 VAC (min) to 132 VAC (max)
High-line (230 VAC nominal)—170 VAC (min) to 264 VAC (max) |
| AC-input current | 16 A @ 100 VAC
7 A @ 240 VAC |
| AC-input frequency | 50/60 Hz (nominal) (±3 Hz for full range) |
| Branch circuit requirement | Each chassis power supply should have its own dedicated, fused-branch circuit:
For North America—15 A or 20 A For International—Circuits sized to local and national codes All Catalyst 4500 E-series AC-input power supplies require single-phase source AC. All AC power supply inputs are fully isolated. – Source AC can be out of phase between multiple power supplies in the same chassis, which means that PS1 can be operating from phase A and PS2 can be operating from phase B. – For high-line operation, the power supply operates with the hot conductor wired to a source AC phase and the neutral conductor wired either to ground or to another source AC phase as long as the net input voltage is in the range of 170 to 264 VAC. – Source AC can be out of phase between AC inputs on power supplies that are equipped with multiple AC inputs, which means that power cord 1 can be plugged into phase A and power cord 2 can be plugged into phase B. |
| Power supply output capacity | 1300 W maximum
1050 W+ 40 W redundant mode (data) 1667 W maximum in combined mode (data) 800 W maximum each in redundant mode (PoE) 1333 W maximum in combined mode (PoE) |
| Power supply output | 84.7 A @ 12 V @ (data)
12.5 A @ 3.3 V (data) 16.7 A @ –50 V (PoE) |
| Output holdup time | 20 ms minimum |
| Maximum kVA rating | 1.76 kVA |
| Max heat dissipation | 1568 BTUs/hr |
| Minimum software requirement | Cisco IOS Release 12.1(12c)EW |
| Power over Ethernet (PoE) | Supported, up to 800 W (211 Cisco phones in combined mode) |
|
Power supply LEDs and their meanings |
|
| INPUT OK | Green—Source AC voltage is OK. (Input voltage is 85 VAC or greater.)
Off—Source AC voltage falls below 70 VAC, is not present, or the power supply is turned off. |
| FAN OK | Green—Power supply fan is operating properly.
Off—Power supply fan failure is detected. |
| OUTPUT FAIL | Red—Problem with one or more of the DC-output voltages of the power supply is detected.
Off—DC-output voltage with acceptable margins. Note For proper operation of the OUTPUT FAIL LED, systems with single power supplies must be configured with a minimum of one fan tray assembly and one supervisor engine. Systems with dual power supplies must have a minimum configuration of one fan tray assembly, one supervisor engine, and one additional module. Failure to meet these minimum configuration requirements can cause a false power supply output fail signal. |
Means of Payment
For your convenience, we accept multiple payment methods in USD, including PayPal, Credit Card, and wire transfer.
RFQ (Request for Quotations)
It is recommended to request for quotations to get the latest prices and inventories about the part.
Our sales will reply to your request by email within 24 hours.
IMPORTANT NOTICE
1. You’ll receive an order information email in your inbox. (Please remember to check the spam folder if you didn’t hear from us).
2. Since inventories and prices may fluctuate to some extent, the sales manager is going to reconfirm the order and let you know if there are any updates.
Shipping Method
Currently, our products are shipped through DHL, FedEx, SF, and UPS.
Delivery Time
Once the goods are shipped, estimated delivery time depends on the shipping methods you chose:
FedEx International, 5-7 business days.
The following are some common countries’ logistic time.
